Group, I ordered the proper gasket material (round) from Hamerhead. It will be along next week. Any pointers I should know before I try to change it. I...
Hello all We are in Hope Town, Abacos, waiting for our new fresh water pump to arrive on the 8th ( they say ) Has anyone replaced this pump themselves. Looks...
Sea Scout donation up for sale. Located in Gulfport, MS -- Hike Harder, Samson Vasquez Sailing Director Gulfport Yacht Club 228-323-1336 ...../)..../).........
Hello We are planning to sail our Niagara 35 out to Newfoundland this summer and haul out there for the winter. Does any one know how many and the best...
My boom was damaged in a storm last summer. After a violent jibe there is a slight buckle on one side of the boom at the outer u-bolt through-holes where the...
Good morning all, We are anchored off Lynyard Cay , just south of Hope Town, Abaco. On our way up here from Royal Island ( Spanish Wells ) the engine alarm...
I have been told by the surveyor that I need to install one on the boat I just purchased. I cannot see that it has one and cannot see where one could be...
Hello all I`m concerned about the metal fitting on the bow , down near the water line, that the bow sprit rod attaches to. Do you know the one ? It appears to...
Has anyone ever had a 3-blade Campbell Sailor propeller? If so, did you like it? I am considering replacing my 2-blade Michigan Wheel prop with one. Rob Max...
Hello all Has anyone out there modified the front of the locker like John Bailey did. I makes it possible to put two 20 lb tanks in. Is john still on line ? I...
Good morning all I definately agree and I know of other boatowners who have copied it directly from N 35 s. merry christmas everyone George ... From: Terry...
Good morning Bob, Your photo , above shows exactly the same rub rail and if you were to check , I think you would find very thick vinyl and finding some is my...
Keep us posted. I for one have a '79 MD11 and would love to know how your project goes and $$. Terry Blythe Spirit #33 ... Keep us posted. I for one have a...
Hello All, I had posted about this in the summer but I though I would try again now that its winter and less people are away from the Internet. My Volvo penta...
Hello all We had a slight mishap and are doing temporary repairs to see us through. However, we hope to be able to source out the " rubber " rub rail at the ...
Hello everyone Well , we finally made it !!. We were up at 03:00 this morning and set off from No Name Harbour, Key Biscayne . We set a course for Bimini and...
I'm an old member with a new name. I'm the owner of Foxfire. Hull #193 She is still located in Punta Gorda Florida. However she is now for sail. Please...
The local Sea Scouts have acquired an N35. It is more then we can handle now. Moat of all of the parts are here even have doubles of most stuff. Owner was busy...
As a result of Hurricane Sandy our boat was damaged and one task will be to replace the port side teak rubrail. Has anyone removed a rubrail from a Niagara...
When I got my Niagara 35 a few years ago both teak rubrails were in bad shape. I decided to remove them and replace them with some kind of vinyl/rubber...
We have a yanmar 38, v-drive and max prop that if I'm not mistaken is pitched to 22 degrees. We never get up to 7 knots, more like 6.75 at full throttle, 2700...
Steve Wiggers at Wiggers Custom Yachts in Bowmanville, Ontario, may have a set of Niagara 35 drawings. I know he has build Nonsuch. I asked him about...
Richard, You may recall you repowered Sunflower with a W-46 (#27) when she was back at the factory. We have no problem getting 7+Kn in the 24-2500 rpm range....
