I know it's easy to forget because most clubs don't have any such "rule"...and in fact some clubs encourage it. No probs. GB ... come here often enough. :(...
Hi folks. I just wanted to repost a question that I had posted before, just in case... I have been experiencing a problem with body filler on my fiberglass ...
i need a list of what to buy for my mask , i am in a rut and dont know what to do . I have resin but it seems way to thin to use .Help me temple your my only...
You may have to expand on your question so that we can answer more direct questions, but I can maybe attempt it: Assuming you want to make a casting from a...
Greetings everyone! I'm looking at doing something a little different. Overall, I am building my costume from scratch, but as for the helmet, I would like to...
Ben@home
benjclayton@...
Feb 1, 2004 8:35 pm
4687
**************************************************************** IMPORTANT The information transmitted is for the use of the intended recipient only and may...
Bishop, Scott
Scott.Bishop@...
Feb 2, 2004 1:48 am
4688
**************************************************************** IMPORTANT The information transmitted is for the use of the intended recipient only and may...
Dewar, Simon
Simon.Dewar@...
Feb 2, 2004 3:12 am
4689
yes that is basically it but how do i do it , how do i get in the tight areas .? Michael <gypsyboy88@...> wrote:You may have to expand on your question so...
Welcome, new inductee, to the holy temple of "The DREMEL". You may find your desire to understand the nature of "The DREMEL" increasing over time, and we...
Ah. That is a little tricky and takes a bit of "patience". What you need to do is pre-cut some small strips of fiberglass material that will fit into the...
I have the same thoughts. But here is what I am trying. No guarantees now, but I'm gonna try. I have a good mask (Classic Action Deluxe). One I finish it...
I have taken the liberty of adding Tim Ketzer's prop and replica web site. Under his "model making" cat. is a good Darth Vader's reveal mask he made. Hopefully...
I'm at work right now, but I can get that for you from my c/a when I get home. you want it flat, not following the contour, correct? Alex ... From: vadermaxq...
What is the proper sequence to light the coin slots on the chestbox? I want to get the timing of them absolutely correctly at least for one of the episodes...
After a few discussions about this, the Temple has come to the conclusion that there is no consistent pattern in the blinking of the chestbox throughout an...
I was mistaken0 it is listed in the links section as "The executor" ... From: Alex Coyne [mailto:alex@...] Sent: Tuesday, February 03, 2004 3:23 PM ...
Thank you. In my continuing search I also found this for the TESB version: According to other Vader costumers on the DVCreations Forum (Put in link), the...
Alex, I am guessing this measurement to be 24-26mm can you confirm this? Thanks! VMQ ... when I get ... when ... you ... blister ... some ... DOES ... from a ...
This raises an issue I was having last summer when I was doing my casting. I had the same problem, and it appeared that the cause was the fact that I had...
What a nightmare! Yahoo is screwing around with my posting ability due to the recent virus threat. I'll try to post this, hopefully you all get it! My original...
VMQ- I sincerely apologize, I just got in to work about 15 minutes ago. My brother went into the hospital last night, and I was a bit distracted, so needless...
No problem at all Alex, I thought that something must have happened and you couldn't respond. I wasn't in a desperate hurry. Thank you for doing that very...
Well, I have set the eyes in place, but I could not get them as narrow as the CA mask that Alex has. They are in place at about 26mm between the flat inner...
Wow, I apologize for all this guys, past 2 days have been insane. My brother is doing well, and hopefully this accepts my post! VMQ- one thing I wanted to...
I must admit that Dremel's are great and I love mine. However I do have a question. There are some very tight places, no matter what size mask and helmet you...
a) multi-speed dremel (comes in real handy) b) fine round tip cutter (usually a ball or cone shapped bit) c) alot of time and patience. Basically, go to your...
